Resetting ERROR E27 Waste ink absorber full Canon PIXMA MP150/MP160

Resetting ERROR E27 Waste ink absorber full Canon PIXMA MP150/MP160



E27 Waste ink absorber full or platen waste ink absorber full

Canon PIXMA MP150 Photo All In One Printer
Take advantage of professional photo printing with a 4800* x 1200 dpi resolution. Canon’s FINE cartridges use minimum 2pl ink droplets. This delivers detailed and vivid prints for all your photos.
Canon PIXMA MP150 Photo All In One Printer Print a photo lab quality 10 x 15 cm borderless photo in approximately 55 seconds in Standard mode*. Get fast borderless output from a small credit card size right up to A4. Or use the PIXMA MP150 as a standalone copier delivering up to 22 copies per minute in mono and up to 17 copies per minute in colour.

Canon PIXMA MP160 All-In-One Photo Printer there’s no need to purchase a separate scanner that will take up extra space in your office. Instead, you can rely on this compact unit to scan with a high resolution of up to 600 by 1200 dpi (optical) and 19,200 by 19,200 dpi (interpolated). With a 48-bit internal color depth and the capability to deal with documents up to 8.5 x 11.7 inches, the MP160 will give you professional results in minutes.

How to clear E27 Waste ink absorber full
1.With the printer powered off but connected to a power source,
press the Power button while pressing and holding the Stop/ Reset button.
2.When the Power is lit, press the Stop/Reset button two times
while pressing and holding the Power button.
3.When releasing the Power button and the Stop / Reset button (regardless of order),
the printer will move into a service mode. (Waiting for menu selection)
4.When the on/off lights in green, press the Stop/Reset button the
specified number of time(s) according to the function listed in the table below.
(Each time the Stop/Reset button is pressed, the LED lights alternately in orange
and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)
5.Turn off the printer.( it must be turn off) then turn it on again.

  • Yahoo! Buzz
  • Mixx
  • Reddit
  • StumbleUpon
  • BlinkList
  • Diigo
  • Google Bookmarks
  • Propeller
  • Tumblr


Comments (10)    Posted in Canon Printer    

Related Posts with Resetting ERROR E27 Waste ink absorber full Canon PIXMA MP150/MP160

Links Download Laptop Drivers for Windows Vista and Windows XP

10 Responses to 'Resetting ERROR E27 Waste ink absorber full Canon PIXMA MP150/MP160'

  1. rishi - November 25th, 2008 at 15:14

    best solution, saved my printer & released my tension..

  2. Alex - January 1st, 2009 at 04:17

    This worked for my Canon MP150, thanks!
    Note: I also disassembled the printer first to clean the Waste Ink Absorber Pads (removed pads, washed with water, then dried and replaced).

  3. Elena Karbanova - May 21st, 2009 at 06:38

    Leave a Reply for Resetting ERROR E27 Waste ink absorber full Canon PIXMA MP150/MP160

  4. Joffre - May 24th, 2009 at 08:28

    I’ve openned up my MP150 and found easily two plastic black bases for the Ink Cartridges to sit on, with a small raised nipple in the center of each, with a small hole in them.

    They are attached to a white plastic carriage/platform to hold them and they also have a small raised nipple in the center of each, but NO Foam OR any other type of absorbent material.anywhere to wash clean.

    The black ‘bases’ came off easily and I cleaned them up, but the white sub bases are a part of this white carriage and they don’t come off, unless you do some major dismantling.

    So far, I have just unscrews the right end off my MP150 to get access to this white Carraige..

    The White carriage moves only a short distance and back again; of 20mm ( like a Typewriter ) from the print area..

    But underneath the White Carriage, I found two plastic ‘tubes’ attached to the underside each of the white nipples and through to deep in the back to another compartment, to a cylindrical plastic object.firmly attached / screwed to the rest of the mechanical parts.

    Is this the Ink waste ‘tank’??

    IF this is a waste tank, HOW dose this ‘tank’ get emptied?? I have tried to see if these tubes would come off and to see IF any ink dribbled out, but, they wouldn’t move.

    OR are they electrical , for the sensors? AND leave them alone??

    I did find ink everywhere, pooling in the plastic cavities of the Frame under the Cartridges and cleaned it up..

    SO, I didn’t find exactly what was mentioned in the Instructions, but something completely, different.

    I did try all last nite to get a copy of the Service Manual for a CANON MP 150, but NO luck.

    Do I JUSTt put it back together and reprogram the Programing?

    ANSWERS????? PLEASE.

    Joffre

  5. Admin - May 24th, 2009 at 08:46

    Yes, Error 27 message is Waste Ink Tank Full, you don’t need open your printer. That you need to do is resetting. Resetting is make ic/eeprom of the printer to be zero. I never recommend to people when get the message to open phicailly their printer. Read carefully this post.

  6. rainier - June 15th, 2009 at 20:16

    after resetting error E27 it becomes zero.how can i set the printer to its normal configuration to start printing again

  7. hartmut - October 7th, 2009 at 21:48

    I searched in german comments to this problem E 27. Nothing useful I could find. First with your explanation I came foreward. Now my printer MP 150
    is going on. Everything is perfect.
    Thank you very much.

  8. Tim - October 21st, 2009 at 17:23

    Can’t get my printer to go into service mode. After steps 1 and 2, the printer boots up and E27 appears. Process: Hold Stop/Reset and press Power. Power lights, then hold Power and press Stop/Reset twice and release. I did this many times at different speeds. Suggestions?

  9. jean renaud - November 16th, 2009 at 08:51

    how to clean up the full waste of my printer mp150 in order to restart printing. My printer can not print by saying printer nose is clogged with waste ink. Tank you.

  10. stella - December 12th, 2009 at 09:28

    i am solving the same problem now, i can’t reset the menu too, but i found other solution, everytime i start the mp150, the screen is shinning with “E”and “8″, so i press the middle green button, the button is for fast color copy, after that the screen show “1″ immediately, and i can use the scanner and printer normally, but it shows “E” again after i turn off the printer. hope it helps u


Leave a Reply for Resetting ERROR E27 Waste ink absorber full Canon PIXMA MP150/MP160

Your Banner Ads Here 336x280 only $75 / Month

RECENT POSTS



Technology Blogs - Blog Rankings