1.    Use the included tape dot to seal the breather holes found on the top of the cartridge (as shown at right) Note: Make sure tape dot is completely covering the holes.
2.    Use a regular piece of tape to seal the hole on the bottom of the cartridge also make sure this hole is completely sealed. (shown below)
3.    With a knife, remove the label to expose the ball bearing underneath. Then use a screw driver to push the ball bearing into the cartridge.
4.    Connect the needle to the syringe and fill with ink.
5.    Inject about 4 ml. of ink into the filling hole until the ink tank is full. Continue Reading »
Refilling Canon Cartridge Canon CLI-8

1.    Use the eyelet screw to remove the plugs located on top of the cartridge.
2.    Connect the needle to the syringe and fill with ink.
3.    Insert the syringe through the filling hole and push into the cartridge. Note: You may feel a slight pressure because the cartridge contains a sponge.
4.    Inject up to 10 ml. of ink, per color, then reseal the cartridge with the plug that was removed from step 1. Continue Reading »
Refilling Canon Cartridge BC-22e (photo)

BCI-3eBk, BCI-3eC, BCI-3eM,
BCI-3eY, BCI-3Bk, BCI-3C, BCI-3M,
BCI-3Y, BCI-3PBk, BCI-3PC, BCI-3PM, BCI-5Bk, BCI-5C, BCI-5M, BCI-5Y, BCI-5PC, BCI-5PM, BCI-8Bk, BCI-8C,
BCI-8M, BCI-8Y, BCI-8PBk, BCI-8PC, BCI-8PM

1.    Use the included tape dot to seal the breather holes found on the top of the cartridge (as shown at right) Note: Make sure tape dot is completely covering the holes.
2.    Use a regular piece of tape to seal the hole on the bottom of the cartridge also make sure this hole is completely sealed. (shown below) Continue Reading »
Refilling Canon Cartridge BCI-3eBk, BCI-3eC, BCI-3eM Etc

1.    The filling holes are located under the label as shown. Just peel back the label leaving it still connected to the cartridge, do not remove completely.
2.    Use the provided eyelet screw to widen the filling hole(s) in the top of the cartridge(s).
3.    Connect the needle to the syringe and fill with ink.
4.    Insert the needle into the widen filling hole. Note: This cartridge has a sponge so you may feel a slight pressure. Inject about 10 ml. of ink, per color until the ink bubbles up.
5.    Pull the label back into place and use a piece of tape to hold it in place. Continue Reading »
Refilling Canon Cartridge BCI-60, BCI-61, BCI-62 (photo)

1.    Use the eyelet screw to remove plug located on the top side of the cartridge.
2.    FOR BX-03 ONLY: A hole must be made on the top of the cartridge by using the hole making tool included in the kit. .
3.    Firmly hold the handle of the tool and begin twisting the tool into the top corner of the cartridge. Continue twisting until it pierces the plastic cover.
4.    Once the plastic to is pierced, making the rest of the hole will go very quickly.
5.    Connect the needle to the syringe and fill with ink.
6.    Insert the syringe through the filling hole and push into the cartridge. Note: You may Continue Reading »
Refilling Canon Cartridge BC-01, BC-02, BC-05, BX-02, BX-03, BC-06 (photo)

1.    With the cartridge upside down, using a screwdriver, push in the ball bearing that seals the filling hole. NOTE: There are several versions of these cartridges. One version has the filling hole under the label on the top of the cartridge. Another version does not have a ball bearing at all. In this case it would be necessary to make a hole for the needle to be inserted.  Make this hole in the same spot where the ball bearing would be located, as shown below.
2.    Seal hole with the plug provided.
3.    Connect the needle to the syringe and fill with ink. Continue Reading »
Refilling Canon Cartridge BJI-201BK HC, BJI-201BK, BJI-201C, BJI-201M, BJI-201Y

1.    Use the eyelet screw to remove plug located on top of the cartridge
2.    Connect the needle to the syringe and fill with ink.
3.    Insert the syringe through the filling hole and push into the cartridge. Note: You may feel a slight pressure because the cartridge contains a sponge.
4.    Inject up to 30 ml. of ink then reseal the cartridge with the plug that was removed from step 1. Continue Reading »
Refilling Canon Cartridge BC-20 & BC-23 High Capacity Cartridge

1.    Use a knife to remove the top of cartridge(s).
2.    Use the included eyelet screw to enlarge the filling hole(s) in the top of the cartridge(s).
3.    Connect the needle to the syringe and fill with ink.
4.    Insert the syringe into the correct filling hole, (See diagram below for filling hole color) and push into the center of the cartridge. Note: You may feel a slight pressure because the cartridge contains a sponge. Continue Reading »
Refilling Canon Cartridge BCI-21 Black & 24 Black BCI-21 Color & 24 Color

1.    Use the eyelet screw to remove the white plug located next to the exit hole.
2.    The plug does not need to be removed completely since the white plug and the exit hole plug are connected.
3.    Connect the needle to the syringe and fill with ink.
4.    Insert the syringe through the filling hole which is found where the white plug was removed.
5.    Inject up to 8 ml. of ink (this cartridge is transparent so you will see the ink level) then
6.    reseal the cartridge with the plug that was removed from step 1. Make sure that the
7.    small plastic tip of the plug sits back into the filling hole. Continue Reading »
Refilling Brother Cartridge LC25Bk, LC25C, LC25M, LC25Y

1.    Lay the cartridge down with the label facing up.
2.    Using the eyelet screw provided, begin twisting the screw into the top of the cartridge
3.    Continue twisting until it pierces the plastic cover.
4.    Once the plastic to is pierced, making the rest of the hole will go very quickly.
5.    Connect the needle to the syringe and fill ink.
6.    Insert the syringe into the hole and inject about 20 ml. of ink Continue Reading »
Refilling Brother Cartridge LC41C, LC41M, LC41Y, LC41BK